North Carolina Soybeans: Glyphosate Resistant Pigweed Control Options

    Palmer Amaranth - Pigweed.

    Glyphosate-resistant Palmer amaranth is wide-spread across the Coastal Plain and is showing up alarmingly fast in the Piedmont. Not all Palmer amaranth in North Carolina is glyphosate-resistant. However, growers are encouraged to assume that all Palmer amaranth is resistant to glyphosate and to react accordingly.

    Growers who currently do not have Palmer amaranth are encouraged to prevent it from becoming established. Learn to recognize the weed and remove any escapes before a seed head is produced.

    A single female Palmer amaranth can produce a half million seed. If the seed were uniformly distributed, that is equivalent to more than 10 seed per square foot over an entire acre.

    Don’t ignore escaped weeds; devastating populations can build up quickly. Clean equipment as well as possible when moving from infested to non-infested fields.

    Rotate crops and chemistry as much as possible. Include corn in the rotation where practical; atrazine-based programs are very effective on Palmer amaranth. Be careful to not negate the benefits of rotation by allowing a crop of seed to be produced after corn harvest. In the fall, Palmer amaranth can go from seed to seed in about 40 days.

    Palmer Amaranth Control in Roundup Ready Soybeans

    Programs for Palmer amaranth control in Roundup Ready soybeans are detailed below. Three key points should be kept in mind. First, a residual herbicide applied preplant or preemergence should always be included in a program. Additional residual control from a postemergence application is also beneficial.

    All of the postemergence options listed below, except Harmony SG, have residual activity on Palmer amaranth.

    The second key point is timing of application. Palmer amaranth should be treated postemergence before it exceeds 4 inches tall. If the weed is resistant to glyphosate, the material mixed with glyphosate must do all the work; hence, the treatment should be applied to weeds of the size appropriate for the tank-mix partner. Remember, this weed can grow an inch or more per day.

    Treating larger weeds not only results in less control, but it can also accelerate selection for resistance to PPO inhibitors (Authority, Blazer, Cobra, Envive, Flexstar, Prefix, Reflex, Valor, others), something we can ill afford.

    Third, fomesafen (the active ingredient in Flexstar and one of the ingredients in Prefix and Flexstar GT) behaves as a contact herbicide. That means good spray coverage is required.

    Herbicide Resistance Info

    Unable to display feed at this time.

    While lower spray volumes and air induction nozzles are fine with glyphosate alone, use of flat-fan nozzles and a spray volume of 15 gallons per acre or more will enhance Palmer amaranth control with Flexstar, Flexstar GT, and Prefix applied postemergence.

    Palmer Amaranth Control in LibertyLink Soybeans

    Management programs for Palmer amaranth in LibertyLink soybeans are basically the same as those for Roundup Ready soybeans (detailed on the back) with the obvious exception that Ignite 280 herbicide is used instead of glyphosate postemergence.

    Growers are encouraged to not abuse this herbicide. Ignite will likely be increasingly important for us in the future, hence we must avoid selection for resistance. Do not depend entirely on Ignite, do not exceed two applications per year, do not cut rates, and treat small weeds (treating large weeds is equivalent to cutting rates, which encourages resistance).

    A residual herbicide or herbicides applied preplant or preemergence is always recommended. Additional residual control can be obtained from Dual Magnum, Warrant, Flexstar, or Prefix mixed with Ignite. Timely application is critical for successful Palmer amaranth control with Ignite. For consistent control, Palmer amaranth must be 4 inches or less when treated.

    A supplemental label was recently issued for Ignite 280 that allows higher application rates on LibertyLink soybeans. The supplemental label allows two in-crop applications, with the first application being 22 to 36 fl oz/acre, and the second application being 22 to 29 fl oz.

    It is suggested that no less than 29 fl oz be applied. Hit them hard, hit them small.

    Ignite is a contact herbicide, hence good coverage is critical. It should be applied in a spray volume of at least 15 gallons per acre using flat-fan nozzles. Air-induction nozzles generally will not provide adequate coverage for a contact herbicide.


    Click Image to Enlarge

    The Latest

    Send press releases to

    View All Events

    [ecs-list-events limit="5" key="start date" order="asc"]
    Send press releases to

    View All Events